CAPG Copper Aluminum PG Clamp-manufacture,factory,supplier from China

CAPG copper-aluminum special-shaped parallel clamp is suitable for the non-load-bearing splicing and branching of aluminum stranded wire, steel core aluminum stranded wire and copper branch wire. Through the re-processing of the profile, the aluminum density is better after the second forging, and the strength of the wire clip is improved. higher. There is a layer of blue epoxy resin on the inside of the wire clip to better isolate the air from the copper-aluminum welding joint and prevent the electrochemical corrosion of the copper-aluminum.

The DTL double-hole round head export copper-aluminum terminal produced by our company is a kind of connector, which is used for crimping terminal blocks of aluminum cables. The crimping tube is made of aluminum and the screw eye is made of copper. It has the advantages of fine workmanship and durability. It is widely used in electrical and electrical industries and other fields.Features:1. The surface is smooth and flat, the edges and corners are round and smooth, and the surface is smooth and no roughness. 2. Material: Copper and Aluminum3. Purpose: Conductive4.

Bimetal PG clamp is used in non-strain tapping or connecting to a line suitable for aluminium and copper conductors.Features:M12 bolts and nuts and washers : mild steelFinish: tin platedMinimum ampere rating: 300ATypeConductor mm²JBTL 16-12016-120JBTL 50-24050-240

The cable lugs Terminals are suitable for the connection of wires, power cables and electrical equipment in the distribution device. It is a connector that connects and protects the aluminum wire and the required connection items. It is preferably pure aluminum, which has good electrical conductivity, high temperature resistance, fast heat dissipation, galvanic corrosion resistance, and long service life.

APG-A1 Aluminum Parallel M&A Clamp is suitable for the non-load-bearing splicing and branching of aluminum stranded wires and steel core aluminum stranded wires.

TJ brass bolts are suitable for connection in power transmission and distribution lines. The red copper material has good electrical conductivity and high resistance to electrical resistance. The bolt design guarantees constant contact pressure; the surface is smooth, without burrs, making the work more stable and calm.

PAL1000 aluminum alloy optical cable insulation strain clamp is a product suitable for overhead insulated conductors. The product is used for cable pull, aluminum alloy body material, PA66 insulation core, stainless steel wire rope, and the product process is die-casting. The high-quality aluminum alloy material has strong corrosion resistance and is not easy to rust and age. The appearance is neat and tidy, and the unique design can well protect the cable.Features:1. Material: high strength aluminum alloy.

Alloy aluminum anchoring bracket CS1500 is a kind of fixed clamp for cable poles, made of cast aluminum alloy. The aluminum alloy telegraph pole bracket produced by our company has a smooth and flat surface, rounded and smooth corners, flat and no roughness, fine workmanship, and durability. Features:1. Breaking load: 10kN2. Package:50 pieces3. Gross weight: 10 kg4. Dimension: 47×31×17cm5. Material: high strength alloy aluminum 

Features:1. Material: aluminum alloy2. Teeth shape, with low resistance, reliable splicing.3. All parts connected completely, can’t lose any one during installation.4. arc hold mostly tightly, conductor can’t be moved. 

The tension clamp NLL-1 is suitable for the overhead lines of 10kv and below. It is used to fix the aluminum stranded wire or the steel core aluminum stranded wire on the tension rod. When used for the overhead insulated aluminum wire, it is used in conjunction with the insulating cover to provide insulation protection. The wedge-shaped strain clamp has the advantages of very small hysteresis loss, light weight, convenient installation, etc., which meets the requirements of energy saving and consumption reduction in the transformation of the national grid.

The bi-metal connector is designed to provide an effective corrosion barrier between the dissimilar metals aluminium and copper.The threads nuts and tapped holes is cut after galvanizing and well greased. All other threads is formed before galvanizing. Each PG is tightened  by two bolts with nuts and washers.

JBL series special-shaped parallel groove clamps are used for the connection of small and medium cross-section aluminum stranded wire or steel core aluminum stranded wire and the steel stranded wire of overhead lightning protection wire at a position that does not bear tension.

Alloy aluminum anchoring bracket CS10 with neutral messenger on poles(wood, concrete etc), excellent in industrial and saline environment, fixed by 2×(14mm or 16mm) bolts or 2 stainless straps 0.75×20mm . It is made by high strength aluminum alloy by casting. Features:1. Breaking load: 12kN2. Package: 100 pieces3. Gross weight: 19 kg 

The wire clamp is composed of a rubber clamp block, a pre-twisted wire and a cast aluminum casing. 1. Enhance the rigidity of the cable hanging point and increase the radius of curvature. The single-line clamp can meet the 30° steering angle, and the double-line clamp can meet the 60° steering angle. 2. It can be ensured that the cable is not subject to large bending stress near the outlet of the wire clamp, so as to avoid local mechanical damage causing strand break or wire breakage.

NLL wedge-shaped tension clamp body is made of high-strength aluminum alloy; the outer shell is smooth and has a long service life; it is easy to install and use; it has no power loss and is an energy-saving certified product.Features:1. Model : wedge type2. Material: high strength alloy aluminum3. Model No.: NLL-34. U bolt number: 3 nos5. Tension strength: 60kN Technical specification: Model1KV Overhead Insulated wire10KV Overhead Insulated wireWire clamping rangeφ (mm)U-boltNominal failure loadNumberdiameterNLL-125～7010～255.0～10.02M1240NLL-250～120

The self-supporting figure 8 optical cable clamp has a flat surface, special material and embedded design, which can well protect the cable. Its technology is superb: high-quality aluminum alloy material, rubber clamp block, reduce wear.

PAL1500 aluminum wedge dead end clamp is used to insulate neutral wire suspension cross-bonded cables(25sqmm to 70sqmm). It can use CS-10 aluminum alloy pole mounted bracket for fix, also can be bolted to the pole with M14&M16 bolt or two stainless steel straps 20mm×0.7mm. Black wedge and wire bail to identify insulated neutral clamp.Features:1. Material: high strength aluminum alloy.

ADSS optical cable suspension clamps are divided into several types according to the size of the line span, such as single-layer pre-twisted wire tangent clamps, single suspension clamps and double suspension clamps. The tangent clamp for ADSS optical cable is mainly used for the cable erection of 100m span, and the single-layer pre-twisted wire suspension clamp is mainly used for the erection of optical cable within the span of 100m-200m.Features: a. The suspension clamp has a larger contact area with the ADSS/OPGW optical cable, the stress is evenly distributed, and there is n

The OPGW grounding clamp consists of a section of aluminum alloy wire, an aluminum alloy clamp (connected to the OPGW optical cable), and all-aluminum terminal blocks (connected to the main material of the iron tower).

The aluminum terminal is pressed by aluminum rod, and made of punching press. It is used for the connection of distribution box, aluminum wire, aluminum cable and other wires. It is preferably pure aluminum, which has good electrical conductivity, high temperature resistance, fast heat dissipation, galvanic corrosion resistance, and long service life.

Wire tension clamp for steel core aluminum stranded wire1. The wire clip has good corrosion resistance; the material is exactly the same as the wire, ensuring that the wire clip has a strong ability to resist electrochemical corrosion. 2. The wire clamp adopts a spiral design, which improves the seismic resistance of the wire, uniform stress distribution, does not damage the wire, and prolongs the service life of the wire. Product technical specification sheet:  Sn Model No.

Insulation strain clamp PAL2000 is used for overhead ABC cable, aluminum alloy main body, nylon PA66 insulation core, stainless steel wire rope. The wedge-shaped insulated aluminum alloy tension clamp produced by our company has a variety of specifications. PAL2000 is used for cables with a diameter of 70sqmm to 150sqmm and a tensile load of 15KN. The length of the wire rope can be customized, and the batch quantity can be printed on the product according to customer needs . Features:1. Material: high strength aluminum alloy.

The NLL wedge-shaped strain clamp has the advantages of very small hysteresis loss, light weight, and convenient installation, which meets the requirements of energy saving and consumption reduction in the transformation of the national grid. The main body of the product is made of aluminum alloy, and the bolts and nuts are made of hot-dip galvanized material.Features:1. Model : wedge type2. Material: high strength alloy aluminum3. Model No.: NLL-24. U bolt number: 2 nos M125. Tension strength: 50kNTechnical specification: Model1KV Overhead Insulated wir

The aluminum alloy suspension clamp is firm, easy to install, sturdy and durable, and adopts low-pressure casting technology; it has strong corrosion resistance, no hysteresis, not easy to break, and strong electrical conductivity. Features:1. Material: high strength alloy aluminum2. Model No.: XGH-33. U bolt number: 2 nos bolts4. Tension strength: 40kNTechnical specification: modelAdapt to wire diameter（mm）Main dimensions（mm）Nominal failure load（KN）reference weight（kg）HCMRLXGH-25.1～12.552.5251618.0166401.0XGH-312.4～1750.5231611.5200401.5XGH-419～23.559.5271613.522