The transformer bracing cross arm is the cross of dimension of 550x50x50x6mm。The cross arm is hot dipped galvanized.All steel members and other parts of fabricated material as delivered is free of warps, local deformation.Bending of flat strap is carried out cold.About surface treatment:All galvanizing is carried out by the hot dip process. The zinc coating is smooth, continuous and uniform. It is free from acid spot and shall not scale, blister or be removable by handling or packing.
اتصل الآن
Galvanized steel cross arm dimensions: 2.5m x 10cm x 10cm x 10mm. Steel Galvanized Bolts and Nuts are equipped. All bolts and nuts made in hot dip galvanized steel and completely threaded.
اتصل الآن
The tie strap is used for tying 11kV or 33kV cross-arms to poles. There are steel galvanized bolts and nuts assembled. All ferrous part is made in hot dip galvanized.
اتصل الآن
The JJ-3 insulation piercing clamp has a main line cross-section of 16-95mm, a branch cross-section of 1.5-10mm, an applicable voltage of 1KV, and a nominal current carrying capacity of 138. It has the characteristics of long service life, high conductivity, and firm wiring.Features: 1. Simple installation: puncture structure, no need to strip the wire, torque nut, constant puncture pressure.2. Thickened shell: Nylon material is used to ensure that it can bear enough pressure.3.
اتصل الآن
Storage kit made of same material as the universal pole clamps(hot dip galvanized steel Q235B) and fabricated in the form of a cross arm and provided with suitable method to affix on the pole.
اتصل الآن
The JJ-3 insulation piercing clamp has a main line cross-section of 16-95mm, a branch cross-section of 1.5-10mm, an applicable voltage of 1KV, and a nominal current carrying capacity of 138. It has the characteristics of long service life, high conductivity, and firm wiring. Features:1. Simple installation: puncture structure, no need to strip the wire, torque nut, constant puncture pressure. 2. Thickened shell: Nylon material is used to ensure that it can bear enough pressure.3.
اتصل الآن
JBL series special-shaped parallel groove clamps are used for the connection of small and medium cross-section aluminum stranded wire or steel core aluminum stranded wire and the steel stranded wire of overhead lightning protection wire at a position that does not bear tension.
اتصل الآن
The cable tie is able to loop and lock fully. Extra tie material left past the lock to prevent pull through. Self-locking design for fast and secure installation provided.The cable tie have maximum diameter capable of bundling two to four service wires and cables with cross-section in the range of 4-25mm2.
اتصل الآن
The hot-dip galvanized hexagonal nut has spiral thread: the thread has a fastening effect, the nut has a smooth cross section, no residual burr, and the thread is neat and clear; smooth and no burr: smooth and bright surface, uniform force, non-slip silk; wear-resistant and high-corrosion resistance : The surface is galvanized, which is not easy to rust.
اتصل الآن
PAL1500 aluminum wedge dead end clamp is used to insulate neutral wire suspension cross-bonded cables(25sqmm to 70sqmm). It can use CS-10 aluminum alloy pole mounted bracket for fix, also can be bolted to the pole with M14&M16 bolt or two stainless steel straps 20mm×0.7mm. Black wedge and wire bail to identify insulated neutral clamp.Features:1. Material: high strength aluminum alloy.
اتصل الآن
Steel belt 20X0.7mm with buckle, tts strength and ductility meet requirements for bending the different size of cables on poles. Steel Buckle can hold a single or double wrapped band configuration.Packing:Steel roll of 50 m is packed in form of closed reel rewind tape in nylon plastic roll.
اتصل الآن
Features: 1. It has all the functions of a single suspension clamp.2.
اتصل الآن
Details and characteristics of strain clamps: 1.U shackle: hot-dip galvanized cast steel U-shaped hanging ring, which is used to connect with the pole tower fastener. 2.Insert ring: Hot-dip galvanized precision cast steel insert ring, which is embedded in the bending head of the U-shaped hanging ring of the tension clamp, which can protect the tension clamp and connect with the extension rod. 3.PD hanging plate: The hot-dip galvanized precision cast steel PD hanging plate is used to connect the embedded ring and the U-shaped hanging ring, and avoid the optical cable at the exit
اتصل الآن
Retention Clamp for ADSS cable single extension 50M span cable diameter 9.0-9.5mmTension splint for ADSS tower is made of forged hot dip galvanized steel.use: for installation and maintenance of aerial construction fiber optic networks.Technical Characteristics1. Fitting material: Steel under ASTM A-362. Minimum yield strength: 250Mpa.3. Minimum tensile strength: 400Mpa4. Post fastening method: By 3/4” steel tape.5. Solder points with smooth and uniform finishes6. Hot dip galvanized according to ASTM A 123 Dimensions1. Fitting base dimensions:
اتصل الآن
Features: 1.The product has been treated with hot-dip galvanizing and has good outdoor anti-corrosion performance. 2.According to the requirements of different optical cables, products that ensure that the optical cable is smaller than the bending radius can be designed. 3.It is convenient to install the pole and tower, the installation is firm, and the optical cable can be well protected to avoid the optical cable from wearing. Purpose: It is used to place the surplus optical cable when the optical cable is connected.
اتصل الآن
Down-lead clamps for rubber towers are used to fix the up and down or up of the optical cable on the tower so that it will not shake and avoid the optical cable from wearing. Features: 1.Wide range of application: It is suitable for skeleton type, layer stranded type, beam tube type armored and non-armored fiber optic cables, and is flexible in use. 2.
اتصل الآن
The strength distribution cable is equipped with rubber pads to offer anti-put on characteristic. the state line is not geared up with rubber pads and isn't sandblasted. due to the fact that there are rubber pads to provide buffering around the cord, the abrasion of the touch floor between the wire and the insulator is prevented. therefore, the energy distribution cable can provide better safety to the wires, and the installation is less difficult and faster.
اتصل الآن
A hoop is a component that uses one material to hug or hoop another material, which is a fastener. There are many types of hoops, cable hoops, telegraph pole hoops, cable hoops, cable hoops, and stainless steel hoops are more commonly used.Technical specification table:
اتصل الآن
Insulation strain clamp PAL2000 is used for overhead ABC cable, aluminum alloy main body, nylon PA66 insulation core, stainless steel wire rope. The wedge-shaped insulated aluminum alloy tension clamp produced by our company has a variety of specifications. PAL2000 is used for cables with a diameter of 70sqmm to 150sqmm and a tensile load of 15KN. The length of the wire rope can be customized, and the batch quantity can be printed on the product according to customer needs . Features:1. Material: high strength aluminum alloy.
اتصل الآن
The self-supporting figure 8 optical cable clamp has a flat surface, special material and embedded design, which can well protect the cable. Its technology is superb: high-quality aluminum alloy material, rubber clamp block, reduce wear.
اتصل الآن
The pole clamp is suitable for connecting the tension suspension clamp and the electric pole. Features: 1. Product manufacturing is strictly controlled and meets production standards. 2.The surface of the product has no burrs and is relatively smooth. 3. Support customization of a variety of special-shaped productsThe hoop device is composed of a hoop plate, a wing plate, a tie rib plate, a bolt and an inner liner. An embedded hoop, which is formed by joining the left and right halves of the hoop.
اتصل الآن
Outer wire length: 1100, 1200, 1300mm Applicable range: within 120m Large fiber optic cable outer diameter: 16mm Grip strength of wire clamp: 10-30KNTensile strength: 50KN Scope of application: ADSS optical cable Components: guy grip wire, thimble clevis, U-shaped hanging ring, extension ring, nut, bolt, closed pin, etc. Features: light, simple structure, easy to install. Conditions of use: Used for fiber optic cable projects with a span of less than 150m, a line turning angle (elevation angle)> 15o, and a cable ultimate tensile strength (UTS) less than 15
اتصل الآن
The down-lead clamp for metal rods is used to fix ADSS on the rod. It is suitable for different cable diameters. It is convenient and reliable to install and has a wide adjustable range.1.Function: Fix the optical cable leading up or down on the pole tower to prevent it from shaking and avoid the optical cable from wearing. 2.Condition: The fiber optic cable line and the continuous poles on the first and end poles. 3.Method: usually install one every 1.5 meters.Technical specification table:
اتصل الآن
ADSS preformed tension set , single-layer twisted wire can be used below 200 meters; high-tension strain clamp, double-layer twisted wire can be used for spans above 200 meters. The technical parameters required for the quotation are: the diameter of the applied wire, the range of use, the tensile force and so on.Composition: inner rods, helical guy grip, thimble clevis, U shackle, extension ring, etc.Product parameter According to different needs, the configuration intensity is 70kNSn Model No.
اتصل الآن