Cu-Al PG Clamp 100sqmm-manufacture,factory,supplier from China

Bimetal PG clamp is used in non-strain tapping or connecting to a line suitable for aluminium and copper conductors.Features:M12 bolts and nuts and washers : mild steelFinish: tin platedMinimum ampere rating: 300ATypeConductor mm²JBTL 16-12016-120JBTL 50-24050-240

CAPG copper-aluminum special-shaped parallel clamp is suitable for the non-load-bearing splicing and branching of aluminum stranded wire, steel core aluminum stranded wire and copper branch wire. Through the re-processing of the profile, the aluminum density is better after the second forging, and the strength of the wire clip is improved. higher. There is a layer of blue epoxy resin on the inside of the wire clip to better isolate the air from the copper-aluminum welding joint and prevent the electrochemical corrosion of the copper-aluminum.

Wire tension clamp for steel core aluminum stranded wire1. The wire clip has good corrosion resistance; the material is exactly the same as the wire, ensuring that the wire clip has a strong ability to resist electrochemical corrosion. 2. The wire clamp adopts a spiral design, which improves the seismic resistance of the wire, uniform stress distribution, does not damage the wire, and prolongs the service life of the wire. Product technical specification sheet:  Sn Model No.

JBL series special-shaped parallel groove clamps are used for the connection of small and medium cross-section aluminum stranded wire or steel core aluminum stranded wire and the steel stranded wire of overhead lightning protection wire at a position that does not bear tension.

The bi-metal connector is designed to provide an effective corrosion barrier between the dissimilar metals aluminium and copper.The threads nuts and tapped holes is cut after galvanizing and well greased. All other threads is formed before galvanizing. Each PG is tightened  by two bolts with nuts and washers.

Anti-corona ring for ADSS is made of Al. Alloy. 1.Select the required model according to the diameter of the optical cable. 2.Each set of strain clamp is equipped with an anti-corona ring.The ADSS optical cable erected on the same pole with the high-voltage overhead transmission line is prone to electrical corrosion at the outlet of the fittings. An anti-corona ring can be installed at the outlet of the ADSS optical cable fittings to suppress the electrical corrosion.

Features: 1.High mechanical strength. 2.Aluminum alloy material, rust proof and waterproof. 3.Spiral design anti corona. Anti-corona ring for ADSS is made of Al. Alloy. 1.Select the required model according to the diameter of the optical cable. 2.Each set of strain clamp is equipped with an anti-corona ring.The ADSS optical cable erected on the same pole with the high-voltage overhead transmission line is prone to electrical corrosion at the outlet of the fittings.

The wire rope clamp is corrosion-resistant, not easy to rust, and has the strength of the wire rope. It is safe to use, beautiful in appearance and smooth in transition. The lifting operation has a large safe load, can resist impact load and has a long service life.

• The elasticity of the C-shaped element can maintain a constant contact pressure between the wire and the clamp for a long time, a constant and sufficiently large contact pressure, and the maximized contact surface can maintain a very low contact resistance for a long time.•Unique structure to ensure that the pressure of the wires (different wire diameters) on both sides is equalized, and the large and small wires are skipped.• Long-term stable and good contact performance: maintenance-free, maintenance-free, reducing maintenance costs.•Scientific and advanced articulated structure, which sav

The wire clamp is composed of a rubber clamp block, a pre-twisted wire and a cast aluminum casing. 1. Enhance the rigidity of the cable hanging point and increase the radius of curvature. The single-line clamp can meet the 30° steering angle, and the double-line clamp can meet the 60° steering angle. 2. It can be ensured that the cable is not subject to large bending stress near the outlet of the wire clamp, so as to avoid local mechanical damage causing strand break or wire breakage.

ADSS optical cable tower with down-lead clamp, optical cable clamp, fixed optical cable clamp.The lead-down clamp is used to lead down the optical cable and fix the optical cable when it is jumpered, which improves the mechanical performance of the clamp. It is mainly used for the communication line of the newly built overhead high-voltage power transmission system of 35kv and above. The stainless steel tube and cable core stranding design is reasonable, and the optical fiber is redundant.

The suspension support hook clamp made of hot dip galvanized steel, the dimension is 120mm （L）and 10mm as diameter of the hook. There is one hole of M14 punched on the base plate. The thickness of the base plate is 3.2mm. 

Features: 1. It has all the functions of a single suspension clamp.2.

Dead end clamp is made of plastic body with very high mechanical and climatic resistance. A stainless steel flexible cord equipped with movable insulating saddle and two sleeves compressed on the ends to prevent detachment from the clamp body.An inner sheath consisting of two insulating plastic wedges for clamping of the neutral carrier without damaging the cable insulation.

The structure of the preformed strain clamp is straightforward, and its pre-twisted cord legs are twisted to form an empty tube, and the rear part is a pre-formed twisted ring. the empty tube shaped via the legs of the pre-twisted twine can generate a robust grip while it's far wound at the wire, and the twisted loop is used to restore the insulator.

The JJC series of low-voltage cable piercing clamps use excellent insulation materials and sufficient materials, which greatly improves the stability of the product and has a long service life. The product models are complete in variety, stable in size and easy to match.

Self-supporting optical cable clamp ADSS optical cable tension clamp is a commonly used ADSS optical cable clamp. The main body material is PA66, stainless steel wire rope, injection molding process, widely used in communication engineering, etc. Mainly used for optical cables with 8-12mm cable diameter. Large quantities are exported to South America, Southeast Asia and other countries and regions.Features:Dimension: 205×90×45mmUnit weight:410gCarton size: 550×410×250mmQuantity per carton : 50 piecesMaterial: Nylon and stainless steelCable diameter: 8-12mmInstallation image: 

APG-A1 Aluminum Parallel M&A Clamp is suitable for the non-load-bearing splicing and branching of aluminum stranded wires and steel core aluminum stranded wires.

The self-supporting fiber optic cable clamp ADSS fiber optic cable tension clamp produced by our company, the specification is 5-8mm, is widely used in various optical fiber communication and network projects. Stainless steel wire rope and PA66 main material, injection molding process, color is black. It has the advantages of convenient use, firm fixation, and reduced working hours.

FTTH fiber-in-the-home clamp, designed for hanging, flat optical cable. The clamp is very easy to install and does not require other tools. It can be easily installed on the hanging bracket by manually adjusting the hanging ring. The clamp is equipped with perforated gaskets, which can increase the load when the optical cable is dropped.

The mounting hook clamp are used on poles such as telegraph poles or cylindrical poles. The main purpose is to form an anchor point and erect an optical fiber line body. The finish is hot-dip galvanized, which is corrosion-resistant and anti-rust. The two sides are transparent, equipped with stainless steel fastening strips, which are firm, stable and beautiful after installation.Usage: Used with 12-20mm steel belt, fixed on the pole.Material: carbon steelDimension：65×65×54mm（L×W×H).Installation image: 

The self-supporting figure 8 optical cable clamp has a flat surface, special material and embedded design, which can well protect the cable. Its technology is superb: high-quality aluminum alloy material, rubber clamp block, reduce wear.

The S shape drop cable clamp is made of steel wire and ABS plastic clamp body, one head with a round steel wire, used to bind the self-supporting drop cable suspension wire, and hang the optical cable on the supporting device.Dimension：136×19.5×15mm（L×W×H).Instruction： Wrap the 2-5mm optical brazing wire in the cylindrical groove of the S part, and fix the optical brazing wire connecting rod.Installation image:Drawing: 

The S type cable clamp is used to bind the self-supporting leather cable suspension wire and hang the optical cable on the supporting device, be steadily strengthened and tightened. There are several colors can be chosen: gray, black, white.Instruction： Wrap the 2-5mm optical brazing wire in the cylindrical groove of the S part, and fix the optical brazing wire connecting rod.Packing: comes in plastic first then put in strong durable cardboard box with labels stick on the outer package. Installation image: