The stay rods is for 40kN LV stays, the diameter of rods is M16, each element/material stay rod, stay base plate, guy grip, top make off, thimble are easy for assembly.A drawing of stay bows complete with thimble:
اتصل الآن
Stay rod is used for sustaining the mechanical load of the stay wires.The stay bow are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: 16mm4. Finish: hot dip galvanized
اتصل الآن
The stay plates are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: 450×450×6mm×22mm hole diameter4. Finish: hot dip galvanized
اتصل الآن
The stay rod is called stay set as well, it is a component used to connect the stay wire to the ground anchor.The stay rod are made of Q235B steel, hot dip galvanized surface treatment which used for LV & MV stay rod assembly installation. Both bow type and tubular type we can supply, the tubular type stay rods MV & LV(M16×1830mm; M20×2440mm)exported to most of African countries. Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: M20×2440mm4. Finish: hot dip galvanized
اتصل الآن
Tension insulators are used for transmission and distribution lines and communication lines, broadcast line terminals, corners or large-span poles, The balance pole is subjected to tensile stress. When in use, the wire and the pull wire pass through the hole and slot, and the tension wire is used for insulation and connection.Features:1. Material: high strength carbon steel2. Application: for stay rod assembly3. Dimension: M16×1830mm4. Finish: hot dip galvanized
اتصل الآن
Stay guy grips are used for stay rod, stay insulator and pole top attachment.
اتصل الآن
The tie strap is used for tying 11kV or 33kV cross-arms to poles. There are steel galvanized bolts and nuts assembled. All ferrous part is made in hot dip galvanized.
اتصل الآن
Stay grips dead ends is the preformed wire type, minimum length is 600mm and finish is galvanized. Thimbles is used with guy grips to support wires through the stay rod eye. A combination of guy grips and pole top make offs is used.Installation image:
اتصل الآن
Galvanized steel pole top make off is generally double wrapped around the pole. 3 strands plus king wire and effective 7 strand stay length for dead end attachment. top to facilitate termination of the stay strand that firms the pole on the earth.Features:1. Material: galvanized steel wire2. Application: for stay rod assembly3. Dimension: 1750 overall length mm4. Finish: hot dip galvanized5. Stay wire diameter: 12mm6. Tensile strength” 63kNProduction drawing: Installation image:
اتصل الآن
The second damper can be used for OPGW tension tower vibration dampers if necessary. Tension assembly is used for OPGW cable route's fixing and anchor shackling. Usually be installed on the terminal tower, tight tension tower and intersection angle tower.OPGW tension tower vibration dampers installation image:
اتصل الآن
The galvanized steel strand is made of galvanized material and is composed of multiple steel wires. It has strong anti-rust, anti-rust ability, corrosion resistance, strong load-bearing, and good toughness. After multiple tensile tests, each steel wire rope has no breaks and no loose strands. The surface is smooth, burr-free, high tensile strength, and small bending radius.
اتصل الآن
Features: 1. The application force has no concentrated point, the stress is uniform, and it has a good protective effect on the optical cable. 2. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension.
اتصل الآن
The hook of the parallel cable clamp can be rotated and fixed at ninety degrees. It is used to fix the optical cable wire, fasten it on the steel strand, and connect and fix the S-shaped fixing member on the steel strand. The stranded stay wire is 2.0mm*7 & 2.2mm*7.Dimension : 50×31.5×80mm(L×W×H)Installation image: Drawing:
اتصل الآن
Tension set ADSS cables installation requires a special tangent assembly or a mechanical dead end at each pole. Tension clamp helical spiral usually with several numbers of rods, such as 7 of rods and thickness of each rod can be different based on different requirements. 2.5mm is the most often cable sizes. And always be compatible with fitting accessories.Sn Model No.
اتصل الآن
A hoop is a component that uses one material to hug or hoop another material, which is a fastener. There are many types of hoops, cable hoops, telegraph pole hoops, cable hoops, cable hoops, and stainless steel hoops are more commonly used.Technical specification table:
اتصل الآن
The preformed dead end is used to fix the cable clamp of the cable of the tower, the iron tower, and the microwave tower. It can replace the U-T clamp and the wedge clamp that are commonly used to fix the cable on the line tower. The unique design makes the tension-resistant structure of the cable simple and reliable. After installation, the empty tube formed by the twisting of the two legs of the pre-twisted wire of the wire clip can be wound on the cable to produce a strong grip. The twisted ring is used to fix the ground anchor. Or on the tower pole.
اتصل الآن
1. The twisting direction of the steel stranded wire and the matching preformed guy grip needs to be the same, and the tensile strength of the galvanized steel wire is 1370N/mm2-1470N/mm2. 2. The white corundum used to increase the friction between the pre-twisted wire and the surface should meet the requirements of GB/T 2479.3. The surface of the preformed guy grip should be smooth and free of defects such as cracks, folds and scars.4. The size and tolerance of the pre-twisted wire The size of the pre-twisted wire should meet the requirements of the design d
اتصل الآن
Dimensions:Height: 460±5mm.Min Dry Aring Distance:235mm. Min Creepage Distance:675mmDiameter Of The Rod:Φ17mm.Coupling Dimensions: Single Ear/ Binaural.Number Of Sheds: 6. Raw Materials:1. End-Fitting:1.1Material: Socket: Cast Iron Or Cast Steel, Hot Dip Galvanized. Ball: Forged Steel, Hot Dip Galvanized.1.2 Minimum Thickness Of The Galvanization:86um.2. Core:2.1 Material: Epoxy& Glass Fiber, Acid-Resistant Type.2.2 Diamter:Φ17mm.3.
اتصل الآن
Insulation strain clamp PAL2000 is used for overhead ABC cable, aluminum alloy main body, nylon PA66 insulation core, stainless steel wire rope. The wedge-shaped insulated aluminum alloy tension clamp produced by our company has a variety of specifications. PAL2000 is used for cables with a diameter of 70sqmm to 150sqmm and a tensile load of 15KN. The length of the wire rope can be customized, and the batch quantity can be printed on the product according to customer needs . Features:1. Material: high strength aluminum alloy.
اتصل الآن
The transformer bracing cross arm is the cross of dimension of 550x50x50x6mm。The cross arm is hot dipped galvanized.All steel members and other parts of fabricated material as delivered is free of warps, local deformation.Bending of flat strap is carried out cold.About surface treatment:All galvanizing is carried out by the hot dip process. The zinc coating is smooth, continuous and uniform. It is free from acid spot and shall not scale, blister or be removable by handling or packing.
اتصل الآن
1. Material: high-quality steel, good electrical conductivity, fast heat dissipation and high temperature resistance.2. Treatment: Advanced technology, hot-forged forming without burrs, smooth surface.3. Strict quality inspection, factory direct sales, quality assurance.Model No.: QH-7Tension strength: 70KNThe main dimensions of the PH extension link meets the requirements of the following figure and table:The meanings of letters and numbers in the models in the table are: number--nominal failure load mark.
اتصل الآن
Drop cable pole fasten clamp is a one-piece design that combines the traditional accessory accessories, and also forms multiple anchor nodes on the wire rod. The small size can be used for 90-140mm poles, and the medium size can be used for 135-230mm poles.CompositionFor pole 80-140mm 100 pieces per Carton Plywood pallet
اتصل الآن
The repair sleeve comprises of two pieces with a provision of seat for sliding of the keeper piece.
اتصل الآن
Retention Clamp for ADSS cable single extension 50M span cable diameter 9.0-9.5mmTension splint for ADSS tower is made of forged hot dip galvanized steel.use: for installation and maintenance of aerial construction fiber optic networks.Technical Characteristics1. Fitting material: Steel under ASTM A-362. Minimum yield strength: 250Mpa.3. Minimum tensile strength: 400Mpa4. Post fastening method: By 3/4” steel tape.5. Solder points with smooth and uniform finishes6. Hot dip galvanized according to ASTM A 123 Dimensions1. Fitting base dimensions:
اتصل الآن