The plastic fisher screw wall plug is made of high-quality PE material, which has strong fixation and is not easy to rotate. A variety of sizes are available for a wide range of applications. Corrosion-resistant, high-density polyethylene has rigidity, hardness and mechanical strength.
اتصل الآن
The c-type hook is used as an accessory for outdoor or indoor wall fiber access. The main purpose is to form an anchor on the wall for the erection and support of the fiber.
اتصل الآن
FTTH drop cable screw eye is a supporting device that is directly screwed to a wooden wall or fixed to a brick-concrete wall with an expansion tube to connect and fix the S fixing member. Cement walls need to be used with expansion plugs.The expansion plug is used in conjunction with the ring hook. It is used as an optical fiber access accessory on the cement wall.
اتصل الآن
FTTH drop cable fisher screw eye is installed on the bracket, used to connect and fix the S fixing piece. The expansion plug is used in conjunction with the ring hook. It is used as an optical fiber access accessory on the cement wall.
اتصل الآن
-Impact: No damage on dropping from altitude ≥ 6m to a hard floor-Vibration: Resistance against vibration of standard sine wave, frequency: 20 Hz, Amplitude: ≥ 5mm, duration: 0.5 hour-Material: durable PVC-Color: light gray or white -Temperature: -10°C up to +70°C-Humidity: Up to 100 %.Specification required for different cable diameter ranges:No.ItemUnitSpecification required for different cable diameter ranges (mm)4.0 ~ 6.346.35~ 8.288.5 ~ 11.711.71 ~ 14.314.31 ~ 19.31.1Diametermm9.8-10.39.8-10.310.8-11.312.0-12.912.0-12.91.2Length mm125012501300135016501.3Gripping section lengthmm
اتصل الآن
The c type hook clamp is used as an accessory for outdoor or indoor wall fiber access. The main purpose is to form an anchor on the wall for the erection and support of the fiber. The hanging part rotates more than 180 degrees, so the wire It can only fall off manually, and the wire will not be unhooked even in a strong wind environment.
اتصل الآن
The medium and high tension strain clamps are composed of a double-layer twisted wire structure. The tensile inner twisted wire is made of galvanized steel wire or aluminum-clad steel wire. The inner wall of the pre-twisted wire is stuck with a layer of fine emery to increase friction. The pre-twisted wire is preformed into four sub-bundles during processing to avoid installation errors and facilitate quick installation. The ends of the pre-twisted wires are bent radially outward to avoid squeezing and damaging the optical cable.
اتصل الآن
The TC insert ring is made of Magang, which has high strength and toughness, high vibration damping and good elongation. Malleable iron generally refers to malleable cast iron, cast iron with a certain chemical composition into a white blank, and then annealed cast iron, which has higher strength, plasticity and impact toughness, and can partially replace carbon steel. Technical characteristics:Model No.: TC-05Bolt size: M14Tension strength: 50KN
اتصل الآن
Cable wall mounted anchoring clamp with ScrewsMaterial: hot dip galvanized steelOur clamp anchoring bracket with the advantages below:1. Reduce cable maintenance expenses, avoid frequent repairs, save operating costs, and users get a better experience. 2. The FTTH technology has been widely used, the construction speed is also very fast, and the technical risk is low.3. It provides a stable and reliable guarantee for fiber to the home, and the efficiency of network usage is improved.
اتصل الآن
ADSS terminating helix dead end is made of aluminum-clad steel wire, and the pre-twisted wire is preformed into a bundle during processing, and a firm layer of emery is glued to the inner wall to increase the grip of the tension clamp under the condition of reducing the side pressure on the optical cable.
اتصل الآن
Preformed inner protection line rods:The material is aluminum-clad steel wire, which is the same material as all the aluminum-clad steel wires of OPPC cable. The inner wall of the protector rods is glued with a layer of gold steel sand through a high-strength polymer water-soluble environmentally friendly adhesive to increase the friction with the optical cable. The rods is preformed into four sub-bundles during production, which is convenient for quick installation.
اتصل الآن
Medium and large tension set are composed of a double-layer twisted wire structure. The tension inner rods is made of galvanized steel wire or aluminum-clad steel wire, and the inner wall of the pre-stranded wire is stuck with a layer of fine emery to increase friction. The inner rods includes 4 groups, during processing in the factory to avoid installation errors and facilitate quick installation. The ends of the pre-twisted wires are bent radially outward to avoid squeezing and damaging the optical cable.
اتصل الآن
1. The twisting direction of the steel stranded wire and the matching preformed guy grip needs to be the same, and the tensile strength of the galvanized steel wire is 1370N/mm2-1470N/mm2. 2. The white corundum used to increase the friction between the pre-twisted wire and the surface should meet the requirements of GB/T 2479.3. The surface of the preformed guy grip should be smooth and free of defects such as cracks, folds and scars.4. The size and tolerance of the pre-twisted wire The size of the pre-twisted wire should meet the requirements of the design d
اتصل الآن
Light short span tension set for ADSS cable diameter 11.0-12.0mm, tension strength 4KN, and max span 120 meters.The tension dead end guy grip is made of galvanized steel wire or aluminum-clad steel wire, and the inner wall of the pre-twisted wire is stuck with a layer of fine emery to increase friction.1.The short span ADSS tension set is used for the installation of ADSS cable, includes ADSS guy grip, Galvanized thimble clevis and U shackle. 2. The structure of the short span ADSS guy grip is simple.
اتصل الآن
ADSS preformed tension set , single-layer twisted wire can be used below 200 meters; high-tension strain clamp, double-layer twisted wire can be used for spans above 200 meters. The technical parameters required for the quotation are: the diameter of the applied wire, the range of use, the tensile force and so on.Composition: inner rods, helical guy grip, thimble clevis, U shackle, extension ring, etc.Product parameter According to different needs, the configuration intensity is 70kNSn Model No.
اتصل الآن
The transformer bracing cross arm is the cross of dimension of 550x50x50x6mm。The cross arm is hot dipped galvanized.All steel members and other parts of fabricated material as delivered is free of warps, local deformation.Bending of flat strap is carried out cold.About surface treatment:All galvanizing is carried out by the hot dip process. The zinc coating is smooth, continuous and uniform. It is free from acid spot and shall not scale, blister or be removable by handling or packing.
اتصل الآن
APG-A1 Aluminum Parallel M&A Clamp is suitable for the non-load-bearing splicing and branching of aluminum stranded wires and steel core aluminum stranded wires.
اتصل الآن
Insulation strain clamp PAL2000 is used for overhead ABC cable, aluminum alloy main body, nylon PA66 insulation core, stainless steel wire rope. The wedge-shaped insulated aluminum alloy tension clamp produced by our company has a variety of specifications. PAL2000 is used for cables with a diameter of 70sqmm to 150sqmm and a tensile load of 15KN. The length of the wire rope can be customized, and the batch quantity can be printed on the product according to customer needs . Features:1. Material: high strength aluminum alloy.
اتصل الآن
Details and characteristics of strain clamps: 1.U shackle: hot-dip galvanized cast steel U-shaped hanging ring, which is used to connect with the pole tower fastener. 2.Insert ring: Hot-dip galvanized precision cast steel insert ring, which is embedded in the bending head of the U-shaped hanging ring of the tension clamp, which can protect the tension clamp and connect with the extension rod. 3.PD hanging plate: The hot-dip galvanized precision cast steel PD hanging plate is used to connect the embedded ring and the U-shaped hanging ring, and avoid the optical cable at the exit
اتصل الآن
The WS-type bowl head hanging plate produced by our company has the characteristics of oxidation resistance, corrosion resistance, and durability. It is suitable for the connection between the insulator string and the fittings, the line clamp and the insulator string, and the lightning protection wire and the pole tower. The main body is made of malleable cast iron, hot-dip galvanized, oxidation-resistant and corrosion-resistant.
اتصل الآن
The repair sleeve comprises of two pieces with a provision of seat for sliding of the keeper piece.
اتصل الآن
1. Material: high-quality steel, good electrical conductivity, fast heat dissipation and high temperature resistance.2. Treatment: Advanced technology, hot-forged forming without burrs, smooth surface.3. Strict quality inspection, factory direct sales, quality assurance.Model No.: QH-7Tension strength: 70KNThe main dimensions of the PH extension link meets the requirements of the following figure and table:The meanings of letters and numbers in the models in the table are: number--nominal failure load mark.
اتصل الآن
According to the size of the object to be bound, it can be cut to any desired length, equipped with stainless steel buckles, and quickly installed with the corresponding strap tightening machine, which is safe, fast and reliable.Material: cast steelSuitable for width of band strap: 9.5-25.0mm Suitable for thickness of band strap: 0.8-1.0mmSurface treatment: sprayed, chrome platedOur tension tool for SS strapping band with the advantages below: 1.It has a wide range of applications and multiple uses.
اتصل الآن
The top tie are all designed in a spiral structure and include aluminum-clad steel wires. the central part of the energy distribution cable is fashioned in the factory, and its form may be matched with diverse insulators and wires.
اتصل الآن