Pole Install Suspension Clamp for ADSS Cable-manufacture,factory,supplier from China

(Total 24 Products for Pole Install Suspension Clamp for ADSS Cable)
Tangent suspension clamp for FOR FIBER OPTIC CABLE ADSS Span 120m Diameter of ADSS cable:  11.8 ± 0.4 mm.  It is mainly used for the installation of optical cables on short-span linear pole towers below 150 meters, or pole towers with a rotation angle of less than 15 degrees.This product has rubber clamps and one-piece aluminum alloy casing (butterfly type).
  اتصل الآن
Suspension set for ADSS features: 1.This product has uniform stress distribution and no stress concentration points, which can enhance the 2. Rigidity of the cable installation point without additional damage to the optical cable; The tangent clamp has a high dynamic stress bearing capacity, which can effectively lift and fix the line; 3.
  اتصل الآن
The down-lead clamp for metal rods is used to fix ADSS on the rod. It is suitable for different cable diameters. It is convenient and reliable to install and has a wide adjustable range.1.Function: Fix the optical cable leading up or down on the pole tower to prevent it from shaking and avoid the optical cable from wearing. 2.Condition: The fiber optic cable line and the continuous poles on the first and end poles. 3.Method: usually install one every 1.5 meters.Technical specification table: 
  اتصل الآن
ADSS optical cable rubber rod down-lead clamp is made of corrosion-resistant, weather-resistant EPDM rubber. It is used for fixing ADSS on the pole tower, suitable for different cable diameters, convenient and reliable installation, and wide adjustable range.1.Function: Fix the optical cable leading up or down on the pole tower to prevent it from shaking and avoid the optical cable from wearing. 2.Condition: The fiber optic cable line and the continuous poles on the first and end poles. 3.Method: usually install one every 1.5 meters.Technical specification table: 
  اتصل الآن
Features: 1.The product has been treated with hot-dip galvanizing and has good outdoor anti-corrosion performance. 2.According to the requirements of different optical cables, products that ensure that the optical cable is smaller than the bending radius can be designed. 3.It is convenient to install the pole and tower, the installation is firm, and the optical cable can be well protected to avoid the optical cable from wearing. Purpose: It is used to place the surplus optical cable when the optical cable is connected.
  اتصل الآن
The performance advantages of ADSS suspension clamp set: (1).The stress of the pre-twisted suspension clamp is distributed in a larger area, which greatly reduces the influence of static stress on the optical cable, greatly improves the ability of the optical cable to withstand stress, and the ADSS suspension clamp has the same effect as the ADSS optical cable. Larger contact area, uniform stress distribution, no stress concentration points, and at the same time enhances the rigidity of the optical cable at the hanging point, which provides better protection.
  اتصل الآن
ADSS optical cable suspension clamps are divided into several types according to the size of the line span, such as single-layer pre-twisted wire tangent clamps, single suspension clamps and double suspension clamps. The tangent clamp for ADSS optical cable is mainly used for the cable erection of 100m span, and the single-layer pre-twisted wire suspension clamp is mainly used for the erection of optical cable within the span of 100m-200m.Features: a. The suspension clamp has a larger contact area with the ADSS/OPGW optical cable, the stress is evenly distributed, and there is n
  اتصل الآن
Material: steelFinish: hot dip galvanized ASTM A123. Usage: pole accessories Type: heavy duty. The cable hoop is a cable in the line to fix the pole. There are flat hoop, reinforced flat hoop, double hoop hoop and four hoop hoop. Generally, the specifications of flat steel and the diameter of the rods to be held are used to express its specifications, such as 60×6×150. Features: 1.
  اتصل الآن
Features: 1. It has all the functions of a single suspension clamp.2.
  اتصل الآن
The pole hoop is used to connect the tension suspension clamp and the electric pole.The cable hoop is a cable in the line to fix the pole. There are flat hoop, reinforced flat hoop, double hoop hoop and four hoop hoop. Generally, the specifications of flat steel and the diameter of the rods to be held are used to express its specifications, such as 60×6×150. Features: 1.
  اتصل الآن
Anchoring clamp pole clamp bracket is composed of CS14 cable bracket and ES 1500 suspension clamp. It is used on poles, in alignment or angle, different levels, also provide for hanging a public light bundle. The anchor pole clamp with stable quality, durable and long service life; neat and burr-free; simplify operation, convenient and easy to use.Features:1. Conductor range: 25-95sqmm2. Package:50 pieces3. Gross weight: 17 kg4. Dimension: 54×31×32cm5. Material: high strength alloy aluminum 
  اتصل الآن
Universal pole bracket UPB is made of aluminum alloy with high mechanical strength. Its unique design has been engineered so to offer an universal pole hardware solution able to adapt to all cable installation configurations on wooden, concrete or metal poles.Features: Working load: 5KNUnit weight:220gCarton size: 420×280×230mmQuantity per carton : 50 piecesMaterial: aluminum alloyDelivery time: 10 daysDrawing: Packing: 50 pieces per carton 
  اتصل الآن
ADSS Suspension Clamps Depending on the application and the fiber optic cable brand, we provide three types of suspension clamps: low tension, medium tension and high tension. Suspension clamps are mainly used on straight iron towers. They are the connection fittings for hanging ADSS optical cables on the towers. They are used to protect the optical cables from damage during erection and operation. The main technical parameters are the breaking force of the clamp (kN) and the cable.
  اتصل الآن
UPB optical cable suspension bracket is a common product for FTTH accessories. The material is aluminum. It is suitable for communication optical fiber engineering dedicated to No. 8 optical cable. It is exported to South America, Southeast Asia, North America, the Middle East and other countries and regions.Features: Dimension: 120×113×45mmUnit weight:210gCarton size: 420×280×230mmQuantity per carton : 50 piecesMaterial: alloyDimension image: Packing image:
  اتصل الآن
Suspension clamps for optical cables are made of real materials, with stable performance and long service life. Composed of insulating clamps and connecting buckles, the stress distribution is even, there is no concentrated point, it can enhance the rigidity of the cable installation point, and the protection performance of the optical cable is good. It has a larger contact area with the optical cable and is equipped with flexible rubber clamps to enhance self-damping and reduce wear.
  اتصل الآن
Suspension string fittings include U-shaped screws, suspension clamps, pre-twisted wire protection lines, grounding drain wires and necessary connection fittings. The mechanical strength of the hanging string connection fittings is 70kN. The suspension clamp is a pre-twisted wire type, and the clamp body is made of aluminum alloy. The clamp body should be equipped with an EPDM rubber cushioning elastic pad. The allowable value of the drape angle at the outlet of the OPGW single drape clamp is not less than 15 degrees.
  اتصل الآن
Tension splint for ADSS tower is made of hot dip galvanized steel.use: Connection of strain clamps, suspension clamps, remaining cable racks and optical cable connection boxes to the iron tower.Technical Parameters: Damage load (kN) and the size of the main material of the power tower at the location of the optical cable hanging point.Configuration method: It can be used in one-to-one correspondence with strain clamps, suspension clamps, remaining cable racks and optical cable splicing boxes.Technical specification list: SnModel No.Unit weight kg1NL-75-1002.82NL-105-1404.23NL-14
  اتصل الآن
The cable hoop is a cable in the line to fix the pole. There are flat hoop, reinforced flat hoop, double hoop hoop and four hoop hoop. Generally, the specifications of flat steel and the diameter of the rods to be held are used to express its specifications, such as 60×6×150. Features: 1.
  اتصل الآن
ADSS suspension clamp material features: 1.Rubber clamp: It is composed of high-quality rubber and aluminum composite plate reinforcement, with chemical resistance, ozone resistance, weather resistance, aging resistance, high and low temperature performance, high strength and elasticity, and can withstand less pressure.
  اتصل الآن
ADSS optical cable suspension clamp components: 1.Aluminum clamp:made of corrosion-resistant aluminum alloy pressure casting, the aluminum alloy has stable chemical properties, good atmospheric corrosion resistance and good mechanical properties. 2.Rubber clamp:Composed of high-quality rubber and center reinforcement, it has the properties of ozone resistance, chemical resistance, weather resistance, high and low temperature performance, high strength and elasticity, and small compression deformation. 3.Bolts, flat washers, spring washers, nuts, closed pins, U-shaped hanging rin
  اتصل الآن
Retention Clamp for ADSS cable single extension 50M span cable diameter 9.0-9.5mmTension splint for ADSS tower is made of forged hot dip galvanized steel.use: for installation and maintenance of aerial construction fiber optic networks.Technical Characteristics1. Fitting material: Steel under ASTM A-362. Minimum yield strength: 250Mpa.3. Minimum tensile strength: 400Mpa4. Post fastening method: By 3/4” steel tape.5. Solder points with smooth and uniform finishes6. Hot dip galvanized according to ASTM A 123 Dimensions1. Fitting base dimensions:
  اتصل الآن
The aluminum alloy suspension clamp is firm, easy to install, sturdy and durable, and adopts low-pressure casting technology; it has strong corrosion resistance, no hysteresis, not easy to break, and strong electrical conductivity. Features:1. Material: high strength alloy aluminum2. Model No.: XGH-33. U bolt number: 2 nos bolts4. Tension strength: 40kNTechnical specification: modelAdapt to wire diameter(mm)Main dimensions(mm)Nominal failure load(KN)reference weight(kg)HCMRLXGH-25.1~12.552.5251618.0166401.0XGH-312.4~1750.5231611.5200401.5XGH-419~23.559.5271613.522
  اتصل الآن
Anti-corona ring for ADSS is made of Al. Alloy. 1.Select the required model according to the diameter of the optical cable. 2.Each set of strain clamp is equipped with an anti-corona ring.The ADSS optical cable erected on the same pole with the high-voltage overhead transmission line is prone to electrical corrosion at the outlet of the fittings. An anti-corona ring can be installed at the outlet of the ADSS optical cable fittings to suppress the electrical corrosion.
  اتصل الآن
The wire clamp is composed of a rubber clamp block, a pre-twisted wire and a cast aluminum casing. 1. Enhance the rigidity of the cable hanging point and increase the radius of curvature. The single-line clamp can meet the 30° steering angle, and the double-line clamp can meet the 60° steering angle. 2. It can be ensured that the cable is not subject to large bending stress near the outlet of the wire clamp, so as to avoid local mechanical damage causing strand break or wire breakage.
  اتصل الآن
Relate News
We sent our pole clamps samples to the National space frame and steel structure quality supervision and inspection center, the samples were tested and meet the technical requirements of standard GB/T 2694-2010. 
The pole clamp is suitable for connecting the anxiety suspension clamp and the electric pole. A big quantity of various varieties of hoops are wanted in overhead strains or whilst putting in pole accessories. it's miles especially easy to put in hoops on equal-diameter poles, just recognize the unique diameter. while installing a hoop on a tapered pole, if the hoop size is simply too massive, you want to insert iron pieces internal; if the ring is too small, the hoop and the telegraph pole cannot in shape together.
The preformed suspension clamp is used for the connection of various wires such as ADSS optical cable and OPGW optical cable in the linear pole tower.
1.extensive variety of applications, torsion resistance and pressure resistance, balanced torsion torque, company and tight locking, and huge adjustment variety. 2.put it at the telegraph pole, tighten and fix it. 3. the poles with diameters of one hundred seventy five-197mm can be adjusted. Pole clamp belt for cable garage bracket is manufactured from c201 stainless-steel, with width of 19mm, thickness of 0.7mm and duration from 1.2m to at least one.5m primarily based on exclusive pole.
The hoop is used to restore the metal strand or cord on the pole, and the pull is much like solving to the wall or other objects to tighten the steel strand. There are numerous styles of hoops, cable hoops, telegraph pole hoops, cable hoops, cable hoops, and stainless-steel hoops are extra usually used.Cement poles can be divided into rectangular, octagonal, i-formed, circular or a few different particular-common go-section poles in step with their cross-sections. amongst them, the extra generally used are spherical bolstered concrete poles.
With the continuous growth of China's national economy as a whole and the influence of the reform of telecommunications system, the market demand for ADSS power optical cable has increased significantly, reaching 10 million core kilometers in 2001.In the 21st century, there were several situations at that time: (1) Domestic optical cable enterprises were affected by the "bubble" of optical network, and the telecom market shrank, and the supply exceeded demand.
Wonderful anti-pressure ability, accurate brief-circuit current ability ;Match with ordinary floor cord l undertake stainless-steel pipe production generation, the pipe is full of water-blocking off compounds, the application version can efficaciously protect the optical fiber ;Using stainless steel tube production technology, the tube filled with water-blocking compounds, can effectively protect the optical fiber;The utility model has the dual functions of a ground wire and a communication optical cable, and avoids the huge cost of repeated erection and maintenance;It is installed on the top
Tools/raw materials Aluminum alloy joint box Pre-twisted suspension clamp Optical cable down lead clamp Cable rack Tower fastener Cable hoop Whip and hammer Pre-twisted hardware1.Before installing the inner twisted wire, pass the outer twisted wire through the embedded ring and make it parallel to the optical cable, and mark the optical cable where the outer twisted wire is colored.2.Winding the first group of inner twisted wires on the optical cable; Align the second group of inner twisted wires with the first group of inner twisted wires, winding the s
Spiral preformed tension clamp and ADSS single-layer tension clamp have similar functions as tension clamp. Spiral preformed tension clamps are mainly used for poles and towers with short spans of 50 to 200 meters, such as corners, tensions, and terminals.
Optical cable joint box, ADSS optical cable joint box, OPGW optical cable joint box, OPPC optical cable joint box Uses: Widely used in ADSS, OPGW special optical cable joints and the junction of different optical cables, and play a role in protecting optical cable joints. Features: 1.The metal splice box is made of aluminum alloy casting, which is especially suitable for the protection of optical cable joints under high-voltage electric fields. 2.The metal splice box overcomes the weakness of the plastic splice box, which is poor in anti-aging ability and short life under t
Wires mainly include bare wires, electromagnetic wires, insulated wires, power cables, communication cables and optical cables for electrical appliances. Electric cable refers to the materials used for power, communication and related transmission purposes. There is no strict boundary between "wire" and "cable".
Mini-Bracket Mini Brackets are used for short and medium spans of ADSS fiber optic cable as well as Aerial Drop cables. Mini Brackets are sized to fit specific ADSS diameters. Standard Mini Brackets are employed with fitted bushings to provide a good support/groove fit and to prevent the support from damaging the cable. The bolted supports are supplied with aluminum captive bolts to simplify installation with no loose parts.