Product advantages: 1. There is a large contact area between the clamp and the pull wire, the stress distribution is even, there is no stress concentration point, and the achievable grip strength is not less than 95% of the stranded wire Calculate the breaking force. 2. The dead end preformed guy grip is made of the same material as the pull wire, which has good corrosion resistance. 3. The dead end preformed guy grip is simple to install, without any special tools, and can be done independently by one person.
اتصل الآن
Stay grips dead ends is the preformed wire type, minimum length is 600mm and finish is galvanized. Thimbles is used with guy grips to support wires through the stay rod eye. A combination of guy grips and pole top make offs is used.Installation image:
اتصل الآن
Helical tension set ADSS long span with D shackle, Thimble clevis, helical dead end, protector rods. A dead-end is installed at each end of the cable length to attach to the structures. Two dead ends are used at angle changes of 30 degree or greater, either horizontal or vertical.
اتصل الآن
ADSS terminating helix dead end is made of aluminum-clad steel wire, and the pre-twisted wire is preformed into a bundle during processing, and a firm layer of emery is glued to the inner wall to increase the grip of the tension clamp under the condition of reducing the side pressure on the optical cable.
اتصل الآن
Preformed helical guy grip clamp with long span helical dead end, thimble clevis, U shackle, link fitting and pole attachment with related accessories.
اتصل الآن
The preformed dead end is used to fix the cable clamp of the cable of the tower, the iron tower, and the microwave tower. It can replace the U-T clamp and the wedge clamp that are commonly used to fix the cable on the line tower. The unique design makes the tension-resistant structure of the cable simple and reliable. After installation, the empty tube formed by the twisting of the two legs of the pre-twisted wire of the wire clip can be wound on the cable to produce a strong grip. The twisted ring is used to fix the ground anchor. Or on the tower pole.
اتصل الآن
The preformed helical guy grip clamp for the conductor is hooked up to the tower by means of its matching fittings, along with insert ring, bowl-head striking plate, and so forth., that could replace conventional bolt-type tension clamps, compression-type anxiety clamps and wedge-type anxiety cables folder.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the product model 4. Pre-twisted wi
اتصل الآن
Dead end clamp is made of plastic body with very high mechanical and climatic resistance. A stainless steel flexible cord equipped with movable insulating saddle and two sleeves compressed on the ends to prevent detachment from the clamp body.An inner sheath consisting of two insulating plastic wedges for clamping of the neutral carrier without damaging the cable insulation.
اتصل الآن
ADSS spiral helical dead end consists of an anchor shackle, thimble clevis and preformed guy grip of suitable length, which used for supporting ADSS fiber optic cable in tension at cable sections, acute turnings or at the terminal pole. -Design for quick and easy installation-Minimizing time consuming civil works -Provide a future proof aerial network-Temperature: -10°C up to +70°CSn Model No. Suitable for ADSS cable range(mm) 300M spanANZ 030/0940 8.6-9.4ANZ 030/1010 9.5-10.1ANZ 030/1070 10.2-10.7ANZ 030/1140 10.8-11.4ANZ 030/1220 11.5-12.2ANZ
اتصل الآن
ADSS spiral helical dead end consists of an anchor shackle, thimble clevis and preformed guy grip of suitable length, which used for supporting ADSS fiber optic cable in tension at cable sections, acute turnings or at the terminal pole. -Design for quick and easy installation-Minimizing time consuming civil works -Provide a future proof aerial network-Temperature: -10°C up to +70°CSn Model No. Suitable for ADSS cable range(mm) 300M spanANZ 030/0940 8.6-9.4ANZ 030/1010 9.5-10.1ANZ 030/1070 10.2-10.7ANZ 030/1140 10.8-11.4ANZ 030/1220 11.5-12.2ANZ
اتصل الآن
The structure of the preformed armor rod and the short protective rod is simple. A set of pre-twisted wires form an empty tube, which generates a gripping force when wrapping the wire, thereby protecting the wire. The pre-twisted wire protection line is used for vibration protection and has been included in the hardware products.
اتصل الآن
Preformed inner protection line rods:The material is aluminum-clad steel wire, which is the same material as all the aluminum-clad steel wires of OPPC cable. The inner wall of the protector rods is glued with a layer of gold steel sand through a high-strength polymer water-soluble environmentally friendly adhesive to increase the friction with the optical cable. The rods is preformed into four sub-bundles during production, which is convenient for quick installation.
اتصل الآن
1. The preformed guy grip is used for the installation of ACSR conductors. The product is with much more reliability and economy compared with the bolt-type & hydraulic strain clamps. 2. The structure of the preformed guy grip is simple. When installation, the tubular structure formed by the legs of the pre-twisted wire can be naturally wound on the conductor to produce a strong grip. The novel structure and unique design make the wire resistant to tension.
اتصل الآن
OPGW Optical Cable Tension Fitting StringFeatures:a. Even stress distribution, no stress concentration point, can well protect the optical cable.b. Under the premise of not exceeding the lateral compression strength of the optical cable, it has a greater grip on the optical cable and can withstand greater tension.c. The grip strength of the optical cable is not less than: 95% of the ultimate tensile strength (UTS) of the optical cable, which is completely suitable for the needs of optical cable erection. Schematic diagram of product composition:Technical specification sheet
اتصل الآن
Stay guy grips are used for stay rod, stay insulator and pole top attachment.
اتصل الآن
Wire tension clamp NL-50/8 for steel core aluminum stranded wire made of galvanized steel wire or alloy clad steel wire. 1. The preformed guy grip is used for the installation of ACSR conductors. The product is with much more reliability and economy compared with the bolt-type & hydraulic strain clamps. 2. The structure of the preformed guy grip is simple. When installation, the tubular structure formed by the legs of the pre-twisted wire can be naturally wound on the conductor to produce a strong grip.
اتصل الآن
Tension set ADSS cables installation requires a special tangent assembly or a mechanical dead end at each pole. Tension clamp helical spiral usually with several numbers of rods, such as 7 of rods and thickness of each rod can be different based on different requirements. 2.5mm is the most often cable sizes. And always be compatible with fitting accessories.Sn Model No.
اتصل الآن
Dimensions:Height: 460±5mm.Min Dry Aring Distance:235mm. Min Creepage Distance:675mmDiameter Of The Rod:Φ17mm.Coupling Dimensions: Single Ear/ Binaural.Number Of Sheds: 6. Raw Materials:1. End-Fitting:1.1Material: Socket: Cast Iron Or Cast Steel, Hot Dip Galvanized. Ball: Forged Steel, Hot Dip Galvanized.1.2 Minimum Thickness Of The Galvanization:86um.2. Core:2.1 Material: Epoxy& Glass Fiber, Acid-Resistant Type.2.2 Diamter:Φ17mm.3.
اتصل الآن
The preformed strain clamp is used to bear full tension on the bare conductors and overhead insulated conductors in the power transmission and distribution line, and connect the conductors to the strain tower, which can replace the conventional bolt-type strain clamp and compression type strain Clamps and wedge-shaped strain clamps.Structure composition and material description 1. Non-twisted ring: standard form, suitable for small diameter wires; Stranded ring: suitable for larger diameter wires 2. Color code: starting mark of installation 3. Label: Indicate the
اتصل الآن
ADSS preformed tension clamp needs to know the outer diameter and force value of the optical cable to request a quotation.
اتصل الآن
Fiber optic tangent used as cable suspension hardware first-rate at the identical time because the attitude of alternate, each horizontal or vertical, is a good deal much less then 15°.Armor grip suspesnion used for any span duration with an perspective change, each horizontal or vertical, a whole lot much less than 30°.There are 3 types of ADSS fitting suspension grips: 1. ADSS fitting for span length less than 70msuspension with suspention rods and protection rods, ring type thimble and pole attachment, steel tip, D shackle with related accessories. 2.
اتصل الآن
Features 1. There is a large contact area between the clamp and the wire, the stress distribution is even, there is no stress concentration point, and the achievable grip strength is not less than 95% of the stranded wire to calculate the breaking force.2. The wire clamp is made of the same material as the wire.3. The wire clamp is simple to install, does not require any complicated tools, and can be completed by one person.
اتصل الآن
Dimensions:Height: 440±5mm.Min Dry Aring Distance:360mm. Min Creepage Distance:900mmDiameter Of The Rod:Φ18mm.Coupling Dimensions: Ball and Socket/ Ball HeadNumber Of Sheds: 9. Raw Materials:1.End-Fitting:1.1Material: Socket: Cast Iron Or Cast Steel, Hot Dip Galvanized. Binaural: Forged Steel, Hot Dip Galvanized.1.2 Minimum Thickness Of The Galvanization:86um.2.Core:2.1 Material: Epoxy& Glass Fiber, Acid-Resistant Type.2.2 Diamter:Φ18mm.3.
اتصل الآن
Dimensions:Height: 355±5mm.Min. Dry Aring Distance:200mm.Min. Creepage Distance:460mmDiameter Of The Rod:Φ17mm.Coupling Dimensions: Clevis/Tongue.Number Of Sheds:4. Raw Materials:1. End-Fitting:1.1Material: Socket: Cast Iron Or Cast Steel, Hot Dip Galvanized. Ball: Forged Steel, Hot Dip Galvanized.1.2 Minimum Thickness Of The Galvanization:86um.2. Core:2.1 Material: Epoxy& Glass Fiber, Acid-Resistant Type.2.2 Diamter:Φ17mm.3.
اتصل الآن